973-674-1700Standoffs, Spacers, Captive, Swage, Male Female Standoffs, Jack Screws, Male Male Standoffs, Handles, Thumb Screws, Thumbscrews, Shoulder Screws, Insulating Washers, Electronic Hardware. | HomeSearchOrderQuoteCrossCatalogRepsTechnicalTermsDistributorsAbout UsContact Us |
| Male-Male Standoffs Technical / Engineering Data | | Male-Male Standoffs Standard e-Catalog | |
|
Material / Shape Selection |
MATERIALS | Choose & write down your material / shape code. Go to next step | SPECIFICATIONS |
ROUND | SQUARE | HEX |
Brass | M01 | M02 | M03 | QQ-B- 626 Comp. 22, 1/2 Hard |
Aluminum | M04 | M05 | M06 | QQ-A- 225a Comp. 2, T-3 |
Stainless Steel, 303 | M07 | M08 | M09 | ASTM-A581,ASTM-A582, QQ-S- 763, Class 303, Cond. A |
Carbon Steel | M10 | M11 | M12 | QQ-S- 633, Class 2 |
Nylon, Natural | M17 | M18 | M19 | MIL-P- 17091B, Grade 101 |
Delrin® | M23 | | M25 | LP392- A |
Stainless Steel, 316 | M29 | | M31 | AMS QQ-S-763, ASTM A276 |
Titanium, Grade 2 | M32 | | M34 | ASTM B348 |
Nylon, Black | M35 | M36 | M37 | ASTM D4066, ASTM D6779, UL 94V2 |
RoHS Compliance Statement  I R.E.A.C.H. Statement I DFARS I WEEE Conflict-Free Minerals Statement I Harmonized Tariff Codes WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
|
|
Properties for Non- Metallic Materials |
Properties | Phenolic Linen Based | Teflon® | Nylon | Lexan® 10% Glass Filled | Delrin® | Ultem® |
Flammability Rating | V-1 | UL HB | UL 94V-2 | V-O | UL94HB | V-O |
Water Absorption (%) 24 hrs. | 0.6 - 0.7 | .02 | 1.5 | 0.15 | 0.25 | 0.25 |
Dielectric Constant (60 cycles) | 5.2 - 5.3 | 2.1 | 10 | 2.9 | 3.7 | 3.15 |
Dielectric Strength 1/8 thickness (v/mil) | 350 | 400 | 300- 400 | 380 | 500 | N/A |
Arc Resistance (sec) | 100 | 200 | 140 | 10 | 129 | 120 |
Tensile Strength (psi) | 6,500- 7,000 | 2,700- 3,100 | 11,200-16,500 | 9,000 | 10,400 | 16,500 |
Heat Resistance (continuous degrees F) | 250-275 | 550 | 250 | 270 | 250 | 340 |
Compression Strength (psi) | 201-235 | 700-1,200 | 4,000 - 11,000 | 12,500 | 18,000 | 22,000 |
|
Plating Selection |
Plating Available On These Materials: Brass, Aluminum,Stainless Steel &Carbon Steel |
AVAILABLE PLATING | Choose & write down your plating code. Go to next step
| PLATING AVAILABLE ON THIS MATERIAL | APPLICABLE SPECIFICATIONS |
Anodize (Sulphuric) Dichromate Seal, Yellow/ Green | F01 | Aluminum | Mil-A- 8625F-Type 2 |
Anodize (Sulphuric) Hot Water Seal, Clear | F02 | Aluminum | Mil-A- 8625F-Type 2, Class 1 |
Anodize (Chromic) Hot Water Seal, Dark Gray | F03 | Aluminum | Mil-A- 8625F-Type 1 |
Anodize- Black | F04 | Aluminum | Mil-A- 8625F- Black, Type 2, Class 2 |
Cadmium Plate, Clear Chromate | F05 | Brass, Carbon Steel | QQ-P- 416, Class 2, Type 2 |
Cadmium Plate, Commercial | F05a | Brass, Carbon Steel | |
Cadmium Plate, Gold Chromate | F06 | Brass, Carbon Steel | QQ-P- 416, Class 2, Type 2 |
Cadmium Plate,Olive Drab | F06a | Brass, Carbon Steel | QQ-P- 416, Type 2, Class 3 |
Nickel Plate | F07 | Brass, Carbon Steel | QQ-N- 290A, Class 1, Grade F |
Chromium Plate (Bright) | F08 | Brass, Carbon Steel | QQ-C- 320B, Class 1, Type 1 |
Chromium Plate, Engineering | F08a | Brass, Carbon Steel | QQ-C- 320B, Class 1, Type 2 |
Chromium Plate Over Nickel Plate | F08c | Brass, Carbon Steel | Mil-QQ-C- 320, Over-Mil-QQ-N- 290 |
Passivate | F09 | Stainless Steel | Mil-F- 14072E (EL) E 300 |
Bright Dip | F11 | Aluminum, Brass | |
Iridite, Clear | F12 | Aluminum | Mil-C- 5541E Mil-DTL- 5541F |
Iridite, Gold #14 | F13 | Aluminum | Mil-C- 5541E Mil-DTL- 5541F |
Alodine 1200 | F13a | Aluminum | |
Black Oxide, Brass | F14 | Brass | Mil-F- 495C |
Black Oxide, Stainless Steel | F15 | Stainless Steel | Mil-C- 13924A, Class 3 |
No Finish *even if there is no finish-this code must be included in part # | F16 | Brass, Aluminum Stainless Steel Carbon Steel All Plastics | |
Hot Tin Dip | F17a | Brass, Carbon Steel | Mil-T- 10727, Type 2 |
Silver Plate | F18 | Brass, Carbon Steel | QQ-S- 365- 0.0002 - 0.0003 |
Electro Tin | F19 | Brass, Carbon Steel | Mil-T-10727, Type 1 |
Electro Tin 60/40 Solder | F19a | Brass, Carbon Steel | M222-Mil-F- 14072 |
Zinc Plate .0002 Thick, Clear Chromate | F21 | Brass, Carbon Steel | ASTM-B- 633, Type 1 |
Zinc Plate .0002 Thick, Yellow /Green Chromate | F21a | Brass, Carbon Steel | ASTM-B- 633, Type 2, (Color Chromate) |
Zinc Plate .0002 Thick, Black Chromate | F21b | Brass, Carbon Steel | ASTM-B- 633,Type 2, (Color Chromate) |
Zinc Plate .0002 Thick, Olive Drab | F21c | Brass, Carbon Steel | ASTM-B- 633, Type 2, (Color Chromate) |
Alkali Caustic Etch | F26 | Aluminum | |
|
Thread Specifications |
*Mix and Match Different Threads and Lengths For Each Part. |
THREAD SIZE | Choose & write down your thread number. Go to next step | X & Y EXTERNAL THREAD LENGTH | D- STANDARD DIAMETERS |
2- 56 | 256 - 1 | .125 | 1/8- 5/32- 3/16 |
2- 56 | 256 - 2 | .156 | 1/8- 5/32- 3/16 |
2- 56 | 256 - 3 | .187 | 1/8- 5/32- 3/16 |
4- 40 | 440 - 1 | .187 | 5/32- 3/16- 1/4- 5/16 |
4- 40 | 440 - 2 | .250 | 5/32- 3/16- 1/4- 5/16 |
6- 32 | 632 - 1 | .250 | 3/16- 1/4- 5/16- 3/8 |
6- 32 | 632 - 2 | .375 | 3/16- 1/4- 5/16- 3/8 |
8- 32 | 832 - 1 | .375 | 1/4- 5/16- 3/8- 1/2 |
8- 32 | 832 - 2 | .437 | 1/4- 5/16- 3/8- 1/2 |
10- 24 | 1024 - 1 | .375 | 1/4- 5/16- 3/8- 1/2 |
10- 24 | 1024 - 2 | .500 | 1/4- 5/16- 3/8- 1/2 |
10- 32 | 1032 - 1 | .375 | 1/4- 5/16- 3/8- 1/2 |
10- 32 | 1032 - 2 | .500 | 1/4- 5/16- 3/8- 1/2 |
1/4- 20 | 1420 - 1 | .500 | 5/16- 3/8- 1/2 |
1/4- 20 | 1420 - 2 | .625 | 5/16- 3/8- 1/2 |
1/4- 28 | 1428 - 1 | .500 | 5/16- 3/8- 1/2 |
1/4- 28 | 1428 - 2 | .625 | 5/16- 3/8- 1/2 |
|
Thread Locking Products Codes |
Choose & write down your OPTIONAL thread locking code. Go back to | THREAD LOCKING PRODUCTS |
PH | ND® PATCH |
RP | ND® 360° RING-PATCH |
PL | ND®PELL-IT |
MS | ND®MICROSPHERES |
VT | ND®VIBRA-TITE |
ST | ND®STRIP-THREAD |
More Info on ND® Thread Locking Products |
Tolerances:For Brass, Aluminum, 303 Stainless Steel, 316 Stainless Steel, Carbon Steel and Titanium Body Length- Length up to 6"± .005 / over 6" ±.010 Thread Length Tolerance is± .005 Tolerances: For Nylon & Delrin® Body Length- For all Lengths the Tolerance is ±.010 Thread Length Tolerance is± .010 Diameter: Standard commercial bar stock tolerances. *No undercut Nylon & Delrin® For Modified Parts or Engineering Assistance: Unicorp offers your firm engineering and design services for customized or modified parts at no additional charge. Please call our Engineering Department. UNICORP, MFR. IDENT. Code No. 04729 |
Phone:973-674-1700Toll Free:1-800-526-1389Fax:973-674-3803 |
UNICORP is a leader in manufacturing stock and custom electronic hardware, handles and precision fasteners used by leading companies in nearly every industry since 1971. 291 Cleveland St, Orange, New Jersey 07050USA Mailing Address:P.O. Box 280, Orange, New Jersey 07051-0280USA Feedback I Legal Notice I CopyrightI Services I Jobs I Contact Us I Email Us I Privacy Statement Copyright©2020, Unicorp Inc.,unicorpinc.com or its affiliates |